Eratherm İzolasyon A.Ş.
Heat loss · Fuel · Cost · CO2

CO2 Emission Reduction Calculation with insulation

The chain from an insulation thickness to a tonne of avoided CO2 is short and it is auditable: heat loss difference, operating hours, boiler or heater efficiency, fuel energy content, emission factor. Every step is a number someone can check, and every step is where an exaggerated claim usually hides.

Heat loss delta by caseFuel and efficiency chainEmission factor sourcingPayback and abatement cost
CO2 emission reduction calculation from industrial insulation improvement
1,000,000+ m²Completed insulation application
15,000+ MWPower plant capacity insulated
20+ yearsEngineering and site experience
3 continentsProject delivery
Scope

Four steps from thickness to tonnes

Each step has an input you own and an assumption we have to declare. Nothing in this calculation should be a number you cannot trace.

01

Heat loss, two cases

Loss from the surface as it is today and as it would be after the change, at the same operating temperature and ambient. The difference is the only thing that counts.

02

Annual energy

Loss multiplied by real operating hours, not calendar hours. Seasonal and intermittent services are handled with an operating profile rather than a single factor.

03

Fuel and efficiency

Heat delivered divided by generation efficiency gives fuel consumed. Efficiency comes from your plant data where it exists and is stated as an assumption where it does not.

04

Emission factor

Fuel converted to CO2 using a published factor, cited by source and year, with the scope boundary stated so the figure can be used in reporting.

Where claims break down

The commonest overstatement is applying an ideal thickness improvement across a whole plant when only part of it is actually defective. We calculate from a surveyed condition, not from a nominal one.

Heat loss and emission calculation chain for insulation improvement
Method

How the saving is calculated

Heat loss for both cases is solved to the same standard used for thickness design, so the energy figure and the design figure cannot disagree. The result is reported as a range with the dominant uncertainty named, rather than as a single confident number.

  • Both cases calculated to EN ISO 12241 or ASTM C680, stated in the report
  • Operating hours from plant records or an agreed operating profile
  • Generation efficiency sourced from plant data where available
  • Emission factor cited with publisher, year and scope boundary
  • Result given as a range, with the input that drives the spread identified
Deliverables

What you receive for the business case and for reporting

Written so it survives review by a finance team and by a sustainability auditor, who will ask different questions of the same numbers.

Calculation report

The full chain from surface condition to tonnes CO2 per year, step by step.

Energy and cost summary

Annual energy saved, fuel saved and cost saved at a stated fuel price.

Emission summary

Tonnes CO2 per year avoided, with factor source and reporting scope stated.

Payback analysis

Simple payback and cost per tonne abated, against the installed cost of the work.

Priority ranking

Where the saving per unit of spend is highest, so the budget goes to the right lines.

Assumption register

Every efficiency, price, hour count and factor used, with its source and date.

Thermographic survey of insulation condition for emission calculation
Survey

The calculation is only as good as the surface condition behind it

An emission claim built on a nominal insulation condition is a guess. The defensible version starts from a survey: which lines are bare, which are wet, which are intact and what each is actually running at. That survey is usually the smaller part of the cost and the whole of the credibility.

  • Thermographic survey to locate and quantify the real losses
  • Bare, damaged and wet sections recorded separately — they behave differently
  • Operating temperatures measured rather than taken from the P&ID
  • Areas quantified so the saving is per square metre of real surface
  • Findings tied to line numbers so the repair scope is directly buildable

Industrial Insulation Catalogue

Engineering scope, calculation and documentation services, material families and application capability in a single document.

Open the 2026 catalogue

Working worldwide

ERATHERM works as an engineering partner for operators, EPC contractors and equipment manufacturers. Calculation, design, documentation and specification work is delivered remotely under the client's document control procedure; inspection, site supervision and application teams are mobilised to site.

  • Europe, the Middle East, Asia, Africa and the Americas
  • EPC-level deliverable documentation
  • Client document control procedure
  • Remote engineering and site mobilisation
Questions

Emission reduction questions we are asked

Can this be used in corporate sustainability reporting?

The calculation is built to be auditable and the emission factor is cited with its scope boundary, which is what a reporting framework requires. Whether it qualifies under your specific scheme depends on that scheme's rules on measurement and verification, and we state the basis clearly so your reporting team can make that judgement.

Why is the result given as a range?

Because operating hours and generation efficiency are rarely known precisely, and a single number hides that. A range with the dominant uncertainty named is more useful to a decision than a precise figure that cannot be defended.

What payback is typical for insulation repair?

It varies too widely for a useful average — bare hot lines pay back very fast, intact systems being upgraded for marginal gain may never pay back. That is exactly why the survey and the ranking matter more than a headline figure.

Do you calculate the embodied carbon of the insulation itself?

We can include it where the manufacturer publishes an environmental product declaration. For most hot service applications the operational saving dominates embodied carbon within the first year, but the comparison should be shown rather than assumed.

Send the survey data or ask us to collect it

We will build the chain from surface condition to tonnes of CO2, state every assumption and rank where the budget delivers the most abatement.